alex/rp-hal-boards
1
0
Fork 0
mirror of https://github.com/italicsjenga/rp-hal-boards.git synced 2024-12-23 04:31:30 +11:00
Code Issues Packages Projects Releases Wiki Activity

Change references to probe-run-rp back to upstream probe-run

Browse source
This commit is contained in:
Jan Niehusmann 2021-11-28 10:21:17 +00:00 committed by 9names
parent fad1dfa259
commit 05e072025d
2 changed files with 7 additions and 12 deletions
Show stats Download patch file Download diff file Expand all files Collapse all files

2
.cargo/config
View file

@ -39,4 +39,4 @@ runner = "elf2uf2-rs -d"
# This runner will find a supported SWD debug probe and flash your RP2040 over
# SWD:
# runner = "probe-run-rp --chip RP2040"
# runner = "probe-run --chip RP2040"

17
README.md
View file

@ -73,7 +73,7 @@ You may also want to install these helpful tools:
# Useful to creating UF2 images for the RP2040 USB Bootloader
cargo install elf2uf2-rs --locked
# Useful for flashing over the SWD pins using a supported JTAG probe
cargo install --git https://github.com/rp-rs/probe-run.git --branch rp2040-support
cargo install probe-run
```
## Packages
@ -258,22 +258,17 @@ debug/JTAG probes. It is based on a library called
[probe-rs](https://github.com/probe-rs/probe-rs). Unlike using, say, OpenOCD,
probe-rs can autodetect your debug probe, which can make it easier to use.
Currently, probe-rs supports the slightly unusual debug hardware in the RP2040,
but the last released probe-run tool (v0.2.6, as of September 2021), does not.
However, there is a special version of probe-run for the RP2040 called
[probe-run-rp](https://github.com/rp-rs/probe-run/tree/rp2040-support).
*Step 1* - Install `probe-run-rp`:
*Step 1* - Install `probe-run`:
```console
$ cargo install --git https://github.com/rp-rs/probe-run.git --branch rp2040-support
$ cargo install probe-run
```
*Step 2* - Make sure your .cargo/config contains the following:
```toml
[target.thumbv6m-none-eabi]
runner = "probe-run-rp --chip RP2040"
runner = "probe-run --chip RP2040"
```
*Step 3* - Connect your USB JTAG/debug probe (such as a Raspberry Pi Pico
@ -282,7 +277,7 @@ programming pins on your RP2040 board. Check the probe has been found by
running:
```console
$ probe-run-rp --chip RP2040 --list-probes
$ probe-run --chip RP2040 --list-probes
The following devices were found:
[0]: J-Link (J-Link) (VID: 1366, PID: 0101, Serial: 000099999999, JLink)
```
@ -291,7 +286,7 @@ There is a SEGGER J-Link connected in the example above - the mesage you see
will reflect the probe you have connected.
*Step 4* - Use `cargo run`, which will compile the code and start the specified
'runner'. As the 'runner' is the `probe-run-rp` tool, it will connect to the
'runner'. As the 'runner' is the `probe-run` tool, it will connect to the
RP2040 via the first probe it finds, and install your firmware into the Flash
connected to the RP2040.