//! # Raspberry Pi Pico (monochome) 128x64 OLED Display with SSD1306 Driver Example //! //! This example assumes you got an 128x64 OLED Display with an SSD1306 driver //! connected to your Raspberry Pi Pico. The +3.3V voltage source of the //! Raspberry Pi Pico will be used, and the output pins 21 and 22 of the board //! (on the lower right). //! //! It will demonstrate how to get an I2C device and use it with the ssd1306 crate. //! Additionally you can also see how to format a number into a string using //! [core::fmt]. //! //! The following diagram will show how things should be connected. //! These displays usually can take 3.3V up to 5V. //! //! ```text //! VCC SCL //! /------------\ /----------\ //! | GND \ / SDA | //! _|USB|_ | /-----\ | | /--------+--\ //! |1 R 40| | / __|__|__|__|___ | | //! |2 P 39| | / | ____________ | | | //! |3 38|- GND --+-/ | |Hello worl| | | | //! |4 P 37| | | |Hello Rust| | | | //! |5 I 36|-+3.3V -/ | |counter: 1| | | | //! |6 C | | | | | | | //! |7 O | | """""""""""" | | | //! | | """"""""""""""" | | //! | | (SSD1306 128x64 OLED Display) | | //! ......... / / //! | | / / //! | 22|-GP17 I2C0 SCL---------------------/ / //! |20 21|-GP16 I2C0 SDA-----------------------/ //! """"""" //! Symbols: //! - (+) crossing lines, not connected //! - (o) connected lines //! ``` //! //! See the `Cargo.toml` file for Copyright and license details. #![no_std] #![no_main] // For string formatting. use core::fmt::Write; // The macro for our start-up function use cortex_m_rt::entry; // Time handling traits: use embedded_time::duration::*; use embedded_time::rate::Extensions; // CountDown timer for the counter on the display: use embedded_hal::timer::CountDown; // Ensure we halt the program on panic (if we don't mention this crate it won't // be linked) use panic_halt as _; // A shorter alias for the Peripheral Access Crate, which provides low-level // register access use rp_pico::hal::pac; // A shorter alias for the Hardware Abstraction Layer, which provides // higher-level drivers. use rp_pico::hal; // For in the graphics drawing utilities like the font // and the drawing routines: use embedded_graphics::{ mono_font::{ascii::FONT_9X18_BOLD, MonoTextStyleBuilder}, pixelcolor::BinaryColor, prelude::*, text::{Baseline, Text}, }; // The display driver: use ssd1306::{prelude::*, Ssd1306}; /// Entry point to our bare-metal application. /// /// The `#[entry]` macro ensures the Cortex-M start-up code calls this function /// as soon as all global variables are initialised. /// /// The function configures the RP2040 peripherals, /// gets a handle on the I2C peripheral, /// initializes the SSD1306 driver, initializes the text builder /// and then draws some text on the display. #[entry] fn main() -> ! { // Grab our singleton objects let mut pac = pac::Peripherals::take().unwrap(); // Set up the watchdog driver - needed by the clock setup code let mut watchdog = hal::Watchdog::new(pac.WATCHDOG); // Configure the clocks // // The default is to generate a 125 MHz system clock let clocks = hal::clocks::init_clocks_and_plls( rp_pico::XOSC_CRYSTAL_FREQ, pac.XOSC, pac.CLOCKS, pac.PLL_SYS, pac.PLL_USB, &mut pac.RESETS, &mut watchdog, ) .ok() .unwrap(); // The single-cycle I/O block controls our GPIO pins let sio = hal::Sio::new(pac.SIO); // Set the pins up according to their function on this particular board let pins = rp_pico::Pins::new( pac.IO_BANK0, pac.PADS_BANK0, sio.gpio_bank0, &mut pac.RESETS, ); // Configure two pins as being I²C, not GPIO let sda_pin = pins.gpio16.into_mode::(); let scl_pin = pins.gpio17.into_mode::(); // Create the I²C driver, using the two pre-configured pins. This will fail // at compile time if the pins are in the wrong mode, or if this I²C // peripheral isn't available on these pins! let i2c = hal::I2C::i2c0( pac.I2C0, sda_pin, scl_pin, 400.kHz(), &mut pac.RESETS, clocks.peripheral_clock, ); // Create the I²C display interface: let interface = ssd1306::I2CDisplayInterface::new(i2c); // Create a driver instance and initialize: let mut display = Ssd1306::new(interface, DisplaySize128x64, DisplayRotation::Rotate0) .into_buffered_graphics_mode(); display.init().unwrap(); // Create a text style for drawing the font: let text_style = MonoTextStyleBuilder::new() .font(&FONT_9X18_BOLD) .text_color(BinaryColor::On) .build(); let timer = hal::Timer::new(pac.TIMER, &mut pac.RESETS); let mut delay = timer.count_down(); let mut count = 0; let mut buf = FmtBuf::new(); loop { buf.reset(); // Format some text into a static buffer: write!(&mut buf, "counter: {}", count).unwrap(); count += 1; // Empty the display: display.clear(); // Draw 3 lines of text: Text::with_baseline("Hello world!", Point::zero(), text_style, Baseline::Top) .draw(&mut display) .unwrap(); Text::with_baseline("Hello Rust!", Point::new(0, 16), text_style, Baseline::Top) .draw(&mut display) .unwrap(); Text::with_baseline(buf.as_str(), Point::new(0, 32), text_style, Baseline::Top) .draw(&mut display) .unwrap(); display.flush().unwrap(); // Wait a bit: delay.start(500.milliseconds()); let _ = nb::block!(delay.wait()); } } /// This is a very simple buffer to pre format a short line of text /// limited arbitrarily to 64 bytes. struct FmtBuf { buf: [u8; 64], ptr: usize, } impl FmtBuf { fn new() -> Self { Self { buf: [0; 64], ptr: 0, } } fn reset(&mut self) { self.ptr = 0; } fn as_str(&self) -> &str { core::str::from_utf8(&self.buf[0..self.ptr]).unwrap() } } impl core::fmt::Write for FmtBuf { fn write_str(&mut self, s: &str) -> core::fmt::Result { let rest_len = self.buf.len() - self.ptr; let len = if rest_len < s.len() { rest_len } else { s.len() }; self.buf[self.ptr..(self.ptr + len)].copy_from_slice(&s.as_bytes()[0..len]); self.ptr += len; Ok(()) } } // End of file