//! Inter-Integrated Circuit (I2C) bus
//!
//! See [Chapter 4 Section 3](https://datasheets.raspberrypi.org/rp2040/rp2040_datasheet.pdf) for more details
//!
//! ## Usage
//! ```no_run
//! use embedded_time::rate::Extensions;
//! use rp2040_hal::{i2c::I2C, gpio::Pins, pac, sio::Sio};
//! let mut peripherals = pac::Peripherals::take().unwrap();
//! let sio = Sio::new(peripherals.SIO);
//! let pins = Pins::new(peripherals.IO_BANK0, peripherals.PADS_BANK0, sio.gpio_bank0, &mut peripherals.RESETS);
//!
//! let mut i2c = I2C::i2c1(
//!     peripherals.I2C1,
//!     pins.gpio18.into_mode(), // sda
//!     pins.gpio19.into_mode(), // scl
//!     400.kHz(),
//!     &mut peripherals.RESETS,
//!     125_000_000.Hz(),
//! );
//!
//! // Scan for devices on the bus by attempting to read from them
//! use embedded_hal::prelude::_embedded_hal_blocking_i2c_Read;
//! for i in 0..=127 {
//!     let mut readbuf: [u8; 1] = [0; 1];
//!     let result = i2c.read(i, &mut readbuf);
//!     if let Ok(d) = result {
//!         // Do whatever work you want to do with found devices
//!         // writeln!(uart, "Device found at address{:?}", i).unwrap();
//!     }
//! }
//!
//! // Write some data to a device at 0x2c
//! use embedded_hal::prelude::_embedded_hal_blocking_i2c_Write;
//! i2c.write(0x2c, &[1, 2, 3]).unwrap();
//!
//! // Write and then read from a device at 0x3a
//! use embedded_hal::prelude::_embedded_hal_blocking_i2c_WriteRead;
//! let mut readbuf: [u8; 1] = [0; 1];
//! i2c.write_read(0x2c, &[1, 2, 3], &mut readbuf).unwrap();
//! ```
//!
//! See [examples/i2c.rs](https://github.com/rp-rs/rp-hal/tree/main/rp2040-hal/examples/i2c.rs)
//! for a complete example
use crate::{
    gpio::pin::bank0::{
        BankPinId, Gpio0, Gpio1, Gpio10, Gpio11, Gpio12, Gpio13, Gpio14, Gpio15, Gpio16, Gpio17,
        Gpio18, Gpio19, Gpio2, Gpio20, Gpio21, Gpio26, Gpio27, Gpio3, Gpio4, Gpio5, Gpio6, Gpio7,
        Gpio8, Gpio9,
    },
    gpio::pin::{FunctionI2C, Pin, PinId},
    resets::SubsystemReset,
    typelevel::Sealed,
};
#[cfg(feature = "eh1_0_alpha")]
use eh1_0_alpha::i2c::blocking as eh1;
use embedded_time::rate::Hertz;
use hal::blocking::i2c::{Read, Write, WriteRead};
use rp2040_pac::{I2C0, I2C1, RESETS};

/// I2C error
#[non_exhaustive]
#[derive(Debug)]
pub enum Error {
    /// I2C abort with error
    Abort(u32),
    /// User passed in a read buffer that was 0 or >255 length
    InvalidReadBufferLength(usize),
    /// User passed in a write buffer that was 0 or >255 length
    InvalidWriteBufferLength(usize),
    /// Target i2c address is out of range
    AddressOutOfRange(u8),
    /// Target i2c address is reserved
    AddressReserved(u8),
}

/// SCL pin
pub trait SclPin<I2C>: Sealed {}

/// SDA pin
pub trait SdaPin<I2C>: Sealed {}

impl SdaPin<I2C0> for Gpio0 {}
impl SclPin<I2C0> for Gpio1 {}

impl SdaPin<I2C1> for Gpio2 {}
impl SclPin<I2C1> for Gpio3 {}

impl SdaPin<I2C0> for Gpio4 {}
impl SclPin<I2C0> for Gpio5 {}

impl SdaPin<I2C1> for Gpio6 {}
impl SclPin<I2C1> for Gpio7 {}

impl SdaPin<I2C0> for Gpio8 {}
impl SclPin<I2C0> for Gpio9 {}

impl SdaPin<I2C1> for Gpio10 {}
impl SclPin<I2C1> for Gpio11 {}

impl SdaPin<I2C0> for Gpio12 {}
impl SclPin<I2C0> for Gpio13 {}

impl SdaPin<I2C1> for Gpio14 {}
impl SclPin<I2C1> for Gpio15 {}

impl SdaPin<I2C0> for Gpio16 {}
impl SclPin<I2C0> for Gpio17 {}

impl SdaPin<I2C1> for Gpio18 {}
impl SclPin<I2C1> for Gpio19 {}

impl SdaPin<I2C0> for Gpio20 {}
impl SclPin<I2C0> for Gpio21 {}

impl SdaPin<I2C1> for Gpio26 {}
impl SclPin<I2C1> for Gpio27 {}

/// I2C peripheral operating in master mode
pub struct I2C<I2C, Pins> {
    i2c: I2C,
    pins: Pins,
}

const TX_FIFO_SIZE: u8 = 16;

fn i2c_reserved_addr(addr: u8) -> bool {
    (addr & 0x78) == 0 || (addr & 0x78) == 0x78
}

macro_rules! hal {
    ($($I2CX:ident: ($i2cX:ident),)+) => {
        $(
            impl<Sda: PinId + BankPinId, Scl: PinId + BankPinId> I2C<$I2CX, (Pin<Sda, FunctionI2C>, Pin<Scl, FunctionI2C>)> {
                /// Configures the I2C peripheral to work in master mode
                pub fn $i2cX<F, SystemF>(
                    i2c: $I2CX,
                    sda_pin: Pin<Sda, FunctionI2C>,
                    scl_pin: Pin<Scl, FunctionI2C>,
                    freq: F,
                    resets: &mut RESETS,
                    system_clock: SystemF) -> Self
                where
                    F: Into<Hertz<u64>>,
                    Sda: SdaPin<$I2CX>,
                    Scl: SclPin<$I2CX>,
                    SystemF: Into<Hertz<u32>>,
                {
                    let freq = freq.into().0;
                    assert!(freq <= 1_000_000);
                    assert!(freq > 0);
                    let freq = freq as u32;

                    i2c.reset_bring_down(resets);
                    i2c.reset_bring_up(resets);

                    i2c.ic_enable.write(|w| w.enable().disabled());

                    i2c.ic_con.modify(|_,w| {
                        w.speed().fast();
                        w.master_mode().enabled();
                        w.ic_slave_disable().slave_disabled();
                        w.ic_restart_en().enabled();
                        w.tx_empty_ctrl().enabled()
                    });

                    i2c.ic_tx_tl.write(|w| unsafe { w.tx_tl().bits(0) });
                    i2c.ic_rx_tl.write(|w| unsafe { w.rx_tl().bits(0) });

                    i2c.ic_dma_cr.write(|w| {
                        w.tdmae().enabled();
                        w.rdmae().enabled()
                    });

                    let freq_in = system_clock.into().0;

                    // There are some subtleties to I2C timing which we are completely ignoring here
                    // See: https://github.com/raspberrypi/pico-sdk/blob/bfcbefafc5d2a210551a4d9d80b4303d4ae0adf7/src/rp2_common/hardware_i2c/i2c.c#L69
                    let period = (freq_in + freq / 2) / freq;
                    let lcnt = period * 3 / 5; // oof this one hurts
                    let hcnt = period - lcnt;

                    // Check for out-of-range divisors:
                    assert!(hcnt <= 0xffff);
                    assert!(lcnt <= 0xffff);
                    assert!(hcnt >= 8);
                    assert!(lcnt >= 8);

                    // Per I2C-bus specification a device in standard or fast mode must
                    // internally provide a hold time of at least 300ns for the SDA signal to
                    // bridge the undefined region of the falling edge of SCL. A smaller hold
                    // time of 120ns is used for fast mode plus.
                    let sda_tx_hold_count = if freq < 1000000 {
                        // sda_tx_hold_count = freq_in [cycles/s] * 300ns * (1s / 1e9ns)
                        // Reduce 300/1e9 to 3/1e7 to avoid numbers that don't fit in uint.
                        // Add 1 to avoid division truncation.
                        ((freq_in * 3) / 10000000) + 1
                    } else {
                        // sda_tx_hold_count = freq_in [cycles/s] * 120ns * (1s / 1e9ns)
                        // Reduce 120/1e9 to 3/25e6 to avoid numbers that don't fit in uint.
                        // Add 1 to avoid division truncation.
                        ((freq_in * 3) / 25000000) + 1
                    };
                    assert!(sda_tx_hold_count <= lcnt - 2);

                    unsafe {
                        i2c.ic_fs_scl_hcnt
                            .write(|w| w.ic_fs_scl_hcnt().bits(hcnt as u16));
                        i2c.ic_fs_scl_lcnt
                            .write(|w| w.ic_fs_scl_lcnt().bits(lcnt as u16));
                        i2c.ic_fs_spklen.write(|w| {
                            w.ic_fs_spklen()
                                .bits(if lcnt < 16 { 1 } else { (lcnt / 16) as u8 })
                        });
                        i2c.ic_sda_hold
                            .modify(|_r,w| w.ic_sda_tx_hold().bits(sda_tx_hold_count as u16));
                    }

                    i2c.ic_enable.write(|w| w.enable().enabled());

                    I2C { i2c, pins: (sda_pin, scl_pin) }
                }

                /// Releases the I2C peripheral and associated pins
                pub fn free(self) -> ($I2CX, (Pin<Sda, FunctionI2C>, Pin<Scl, FunctionI2C>)) {
                    (self.i2c, self.pins)
                }
            }

            impl<PINS> I2C<$I2CX, PINS> {
                /// Number of bytes currently in the TX FIFO
                #[inline]
                fn tx_fifo_used(&self) -> u8 {
                    self.i2c.ic_txflr.read().txflr().bits()
                }

                /// Remaining capacity in the TX FIFO
                #[inline]
                fn tx_fifo_free(&self) -> u8 {
                    TX_FIFO_SIZE - self.tx_fifo_used()
                }

                /// TX FIFO is at capacity
                #[inline]
                fn tx_fifo_full(&self) -> bool {
                    self.tx_fifo_free() == 0
                }
            }

            impl<PINS> Write for I2C<$I2CX, PINS> {
                type Error = Error;

                fn write(&mut self, addr: u8, bytes: &[u8]) -> Result<(), Error> {
                    // TODO support transfers of more than 255 bytes
                    if (bytes.len() > 255 || bytes.len() == 0) {
                        return Err(Error::InvalidWriteBufferLength(bytes.len()));
                    } else if addr >= 0x80 {
                        return Err(Error::AddressOutOfRange(addr));
                    } else if i2c_reserved_addr(addr) {
                        return Err(Error::AddressReserved(addr));
                    }

                    self.i2c.ic_enable.write(|w| w.enable().disabled());
                    self.i2c
                        .ic_tar
                        .write(|w| unsafe { w.ic_tar().bits(addr as u16) });
                    self.i2c.ic_enable.write(|w| w.enable().enabled());

                    let mut abort = false;
                    let mut abort_reason = 0;

                    for (i, byte) in bytes.iter().enumerate() {
                        let last = i == bytes.len() - 1;

                        self.i2c.ic_data_cmd.write(|w| {
                            if last {
                                w.stop().enable();
                            } else {
                                w.stop().disable();
                            }
                            unsafe { w.dat().bits(*byte) }
                        });

                        // Wait until the transmission of the address/data from the internal
                        // shift register has completed. For this to function correctly, the
                        // TX_EMPTY_CTRL flag in IC_CON must be set. The TX_EMPTY_CTRL flag
                        // was set in i2c_init.
                        while self.i2c.ic_raw_intr_stat.read().tx_empty().is_inactive() {}

                        abort_reason = self.i2c.ic_tx_abrt_source.read().bits();
                        if abort_reason != 0 {
                            // Note clearing the abort flag also clears the reason, and
                            // this instance of flag is clear-on-read! Note also the
                            // IC_CLR_TX_ABRT register always reads as 0.
                            self.i2c.ic_clr_tx_abrt.read().clr_tx_abrt();
                            abort = true;
                        }

                        if abort || last {
                            // If the transaction was aborted or if it completed
                            // successfully wait until the STOP condition has occured.

                            while self.i2c.ic_raw_intr_stat.read().stop_det().is_inactive() {}

                            self.i2c.ic_clr_stop_det.read().clr_stop_det();
                        }

                        // Note the hardware issues a STOP automatically on an abort condition.
                        // Note also the hardware clears RX FIFO as well as TX on abort,
                        // ecause we set hwparam IC_AVOID_RX_FIFO_FLUSH_ON_TX_ABRT to 0.
                        if abort {
                            break;
                        }
                    }

                    if abort {
                        Err(Error::Abort(abort_reason))
                    } else {
                        Ok(())
                    }
                }
            }

            impl<PINS> WriteRead for I2C<$I2CX, PINS> {
                type Error = Error;

                fn write_read(&mut self, addr: u8, bytes: &[u8], buffer: &mut [u8]) -> Result<(), Error> {
                    // TODO support transfers of more than 255 bytes
                    if (bytes.len() > 255 || bytes.len() == 0) {
                        return Err(Error::InvalidWriteBufferLength(bytes.len()));
                    } else if (buffer.len() > 255 || buffer.len() == 0) {
                        return Err(Error::InvalidReadBufferLength(buffer.len()));
                    } else if addr >= 0x80 {
                        return Err(Error::AddressOutOfRange(addr));
                    } else if i2c_reserved_addr(addr) {
                        return Err(Error::AddressReserved(addr));
                    }

                    self.i2c.ic_enable.write(|w| w.enable().disabled());
                    self.i2c
                        .ic_tar
                        .write(|w| unsafe { w.ic_tar().bits(addr as u16) });
                    self.i2c.ic_enable.write(|w| w.enable().enabled());

                    let mut abort = false;
                    let mut abort_reason = 0;

                    for byte in bytes {
                        self.i2c.ic_data_cmd.write(|w| {
                            w.stop().disable();
                            unsafe { w.dat().bits(*byte) }
                        });

                        // Wait until the transmission of the address/data from the internal
                        // shift register has completed. For this to function correctly, the
                        // TX_EMPTY_CTRL flag in IC_CON must be set. The TX_EMPTY_CTRL flag
                        // was set in i2c_init.
                        while self.i2c.ic_raw_intr_stat.read().tx_empty().is_inactive() {}

                        abort_reason = self.i2c.ic_tx_abrt_source.read().bits();
                        if abort_reason != 0 {
                            // Note clearing the abort flag also clears the reason, and
                            // this instance of flag is clear-on-read! Note also the
                            // IC_CLR_TX_ABRT register always reads as 0.
                            self.i2c.ic_clr_tx_abrt.read().clr_tx_abrt();
                            abort = true;
                        }

                        if abort {
                            // If the transaction was aborted or if it completed
                            // successfully wait until the STOP condition has occured.

                            while self.i2c.ic_raw_intr_stat.read().stop_det().is_inactive() {}

                            self.i2c.ic_clr_stop_det.read().clr_stop_det();
                        }

                        // Note the hardware issues a STOP automatically on an abort condition.
                        // Note also the hardware clears RX FIFO as well as TX on abort,
                        // ecause we set hwparam IC_AVOID_RX_FIFO_FLUSH_ON_TX_ABRT to 0.
                        if abort {
                            break;
                        }
                    }

                    for (i, byte) in buffer.iter_mut().enumerate() {
                        let first = i == 0;
                        let last = i == bytes.len() - 1;

                        // wait until there is space in the FIFO to write the next byte
                        while self.tx_fifo_full()  {}

                        self.i2c.ic_data_cmd.write(|w| {
                            if first {
                                w.restart().enable();
                            } else {
                                w.restart().disable();
                            }

                            if last {
                                w.stop().enable();
                            } else {
                                w.stop().disable();
                            }

                            w.cmd().read()
                        });

                        while !abort && self.i2c.ic_rxflr.read().bits() == 0 {
                            abort_reason = self.i2c.ic_tx_abrt_source.read().bits();
                            abort = self.i2c.ic_clr_tx_abrt.read().bits() > 0;
                        }

                        if abort {
                            break;
                        }

                        *byte = self.i2c.ic_data_cmd.read().dat().bits();
                    }

                    if abort {
                        Err(Error::Abort(abort_reason))
                    } else {
                        Ok(())
                    }
                }
            }

            impl<PINS> Read for I2C<$I2CX, PINS> {
                type Error = Error;

                fn read(&mut self, addr: u8, buffer: &mut [u8]) -> Result<(), Error> {
                    // TODO support transfers of more than 255 bytes
                    if (buffer.len() > 255 || buffer.len() == 0) {
                        return Err(Error::InvalidReadBufferLength(buffer.len()));
                    } else if addr >= 0x80 {
                        return Err(Error::AddressOutOfRange(addr));
                    } else if i2c_reserved_addr(addr) {
                        return Err(Error::AddressReserved(addr));
                    }

                    self.i2c.ic_enable.write(|w| w.enable().disabled());
                    self.i2c
                        .ic_tar
                        .write(|w| unsafe { w.ic_tar().bits(addr as u16) });
                    self.i2c.ic_enable.write(|w| w.enable().enabled());

                    let mut abort = false;
                    let mut abort_reason = 0;

                    let lastindex = buffer.len() -1;
                    for (i, byte) in buffer.iter_mut().enumerate() {
                        let first = i == 0;
                        let last = i == lastindex;

                        // wait until there is space in the FIFO to write the next byte
                        while self.tx_fifo_full()  {}

                        self.i2c.ic_data_cmd.write(|w| {
                            if first {
                                w.restart().enable();
                            } else {
                                w.restart().disable();
                            }

                            if last {
                                w.stop().enable();
                            } else {
                                w.stop().disable();
                            }

                            w.cmd().read()
                        });

                        while !abort && self.i2c.ic_rxflr.read().bits() == 0 {
                            abort_reason = self.i2c.ic_tx_abrt_source.read().bits();
                            abort = self.i2c.ic_clr_tx_abrt.read().bits() > 0;
                        }

                        if abort {
                            break;
                        }

                        *byte = self.i2c.ic_data_cmd.read().dat().bits();
                    }

                    if abort {
                        Err(Error::Abort(abort_reason))
                    } else {
                        Ok(())
                    }
                }
            }

            #[cfg(feature = "eh1_0_alpha")]
            impl<PINS> eh1::Write for I2C<$I2CX, PINS> {
                type Error = Error;

                fn write(&mut self, addr: u8, bytes: &[u8]) -> Result<(), Error> {
                    Write::write(self, addr, bytes)
                }
            }
            #[cfg(feature = "eh1_0_alpha")]
            impl<PINS> eh1::WriteRead for I2C<$I2CX, PINS> {
                type Error = Error;
                fn write_read(&mut self, addr: u8, bytes: &[u8], buffer: &mut [u8]) -> Result<(), Error> {
                        WriteRead::write_read(self, addr, bytes, buffer)
                }
            }
            #[cfg(feature = "eh1_0_alpha")]
            impl<PINS> eh1::Read for I2C<$I2CX, PINS> {
                type Error = Error;

                fn read(&mut self, addr: u8, buffer: &mut [u8]) -> Result<(), Error> {
                    Read::read(self, addr, buffer)
                }
            }

         )+
    }
}

hal! {
    I2C0: (i2c0),
    I2C1: (i2c1),
}