mirror of
https://github.com/italicsjenga/rp-hal-boards.git
synced 2024-12-24 05:01:31 +11:00
107 lines
3 KiB
Rust
107 lines
3 KiB
Rust
//! # I²C Example
|
|
//!
|
|
//! This application demonstrates how to talk to I²C devices with an RP2040.
|
|
//!
|
|
//! It may need to be adapted to your particular board layout and/or pin assignment.
|
|
//!
|
|
//! See the `Cargo.toml` file for Copyright and licence details.
|
|
|
|
#![no_std]
|
|
#![no_main]
|
|
|
|
// The macro for our start-up function
|
|
use cortex_m_rt::entry;
|
|
|
|
// Ensure we halt the program on panic (if we don't mention this crate it won't
|
|
// be linked)
|
|
use panic_halt as _;
|
|
|
|
// Some traits we need
|
|
use embedded_hal::blocking::i2c::Write;
|
|
use embedded_time::rate::Extensions;
|
|
|
|
// Alias for our HAL crate
|
|
use rp2040_hal as hal;
|
|
|
|
// A shorter alias for the Peripheral Access Crate, which provides low-level
|
|
// register access
|
|
use hal::pac;
|
|
|
|
/// The linker will place this boot block at the start of our program image. We
|
|
/// need this to help the ROM bootloader get our code up and running.
|
|
#[link_section = ".boot2"]
|
|
#[used]
|
|
pub static BOOT2: [u8; 256] = rp2040_boot2::BOOT_LOADER;
|
|
|
|
/// External high-speed crystal on the Raspberry Pi Pico board is 12 MHz. Adjust
|
|
/// if your board has a different frequency
|
|
const XTAL_FREQ_HZ: u32 = 12_000_000u32;
|
|
|
|
/// Entry point to our bare-metal application.
|
|
///
|
|
/// The `#[entry]` macro ensures the Cortex-M start-up code calls this function
|
|
/// as soon as all global variables are initialised.
|
|
///
|
|
/// The function configures the RP2040 peripherals, then performs a single I²C
|
|
/// write to a fixed address.
|
|
#[entry]
|
|
fn main() -> ! {
|
|
let mut pac = pac::Peripherals::take().unwrap();
|
|
|
|
// Set up the watchdog driver - needed by the clock setup code
|
|
let mut watchdog = hal::watchdog::Watchdog::new(pac.WATCHDOG);
|
|
|
|
// Configure the clocks
|
|
let clocks = hal::clocks::init_clocks_and_plls(
|
|
XTAL_FREQ_HZ,
|
|
pac.XOSC,
|
|
pac.CLOCKS,
|
|
pac.PLL_SYS,
|
|
pac.PLL_USB,
|
|
&mut pac.RESETS,
|
|
&mut watchdog,
|
|
)
|
|
.ok()
|
|
.unwrap();
|
|
|
|
// The single-cycle I/O block controls our GPIO pins
|
|
let sio = hal::sio::Sio::new(pac.SIO);
|
|
|
|
// Set the pins to their default state
|
|
let pins = hal::gpio::Pins::new(
|
|
pac.IO_BANK0,
|
|
pac.PADS_BANK0,
|
|
sio.gpio_bank0,
|
|
&mut pac.RESETS,
|
|
);
|
|
|
|
// Configure two pins as being I²C, not GPIO
|
|
let sda_pin = pins.gpio18.into_mode::<hal::gpio::FunctionI2C>();
|
|
let scl_pin = pins.gpio19.into_mode::<hal::gpio::FunctionI2C>();
|
|
// let not_an_scl_pin = pins.gpio20.into_mode::<hal::gpio::FunctionI2C>();
|
|
|
|
// Create the I²C drive, using the two pre-configured pins. This will fail
|
|
// at compile time if the pins are in the wrong mode, or if this I²C
|
|
// peripheral isn't available on these pins!
|
|
let mut i2c = hal::i2c::I2C::i2c1(
|
|
pac.I2C1,
|
|
sda_pin,
|
|
scl_pin, // Try `not_an_scl_pin` here
|
|
400.kHz(),
|
|
&mut pac.RESETS,
|
|
clocks.peripheral_clock,
|
|
);
|
|
|
|
// Write three bytes to the I²C device with 7-bit address 0x2C
|
|
i2c.write(0x2c, &[1, 2, 3]).unwrap();
|
|
|
|
// Demo finish - just loop until reset
|
|
|
|
#[allow(clippy::empty_loop)]
|
|
loop {
|
|
// Empty loop
|
|
}
|
|
}
|
|
|
|
// End of file
|