mirror of
https://github.com/italicsjenga/rp-hal-boards.git
synced 2024-12-24 05:01:31 +11:00
b81955c2a8
* Update changelog for 0.4.0 release * Enable rt feature for irq example in Cargo.toml * Bump pio/pio-proc deps to 0.2.0, update pio examples * Update BSPs to latest ws2812-pio, remove unused pio dep * Fix usage of pio_proc in doc comment * Clean up pio doc-example * Update rp-pico to latest i2c-pio Co-authored-by: Jan Niehusmann <jan@gondor.com>
63 lines
1.7 KiB
Rust
63 lines
1.7 KiB
Rust
//! This example toggles the GPIO25 pin, using a PIO program compiled via pio_proc::pio!().
|
|
//!
|
|
//! If a LED is connected to that pin, like on a Pico board, the LED should blink.
|
|
//!
|
|
//! This example makes use of side setting.
|
|
#![no_std]
|
|
#![no_main]
|
|
|
|
use cortex_m_rt::entry;
|
|
use hal::gpio::{FunctionPio0, Pin};
|
|
use hal::pac;
|
|
use hal::pio::PIOExt;
|
|
use hal::Sio;
|
|
use panic_halt as _;
|
|
use rp2040_hal as hal;
|
|
|
|
#[link_section = ".boot2"]
|
|
#[used]
|
|
pub static BOOT2: [u8; 256] = rp2040_boot2::BOOT_LOADER_W25Q080;
|
|
|
|
#[entry]
|
|
fn main() -> ! {
|
|
let mut pac = pac::Peripherals::take().unwrap();
|
|
|
|
let sio = Sio::new(pac.SIO);
|
|
let pins = hal::gpio::Pins::new(
|
|
pac.IO_BANK0,
|
|
pac.PADS_BANK0,
|
|
sio.gpio_bank0,
|
|
&mut pac.RESETS,
|
|
);
|
|
|
|
// configure LED pin for Pio0.
|
|
let _led: Pin<_, FunctionPio0> = pins.gpio25.into_mode();
|
|
// PIN id for use inside of PIO
|
|
let led_pin_id = 25;
|
|
|
|
// Define some simple PIO program.
|
|
let program = pio_proc::pio_asm!(
|
|
".side_set 1", // each instruction may set 1 bit
|
|
".wrap_target",
|
|
" nop side 1",
|
|
" nop side 0",
|
|
".wrap",
|
|
);
|
|
|
|
// Initialize and start PIO
|
|
let (mut pio, sm0, _, _, _) = pac.PIO0.split(&mut pac.RESETS);
|
|
let installed = pio.install(&program.program).unwrap();
|
|
let div = 0f32; // as slow as possible (0 is interpreted as 65536)
|
|
let (mut sm, _, _) = rp2040_hal::pio::PIOBuilder::from_program(installed)
|
|
.side_set_pin_base(led_pin_id)
|
|
.clock_divisor(div)
|
|
.build(sm0);
|
|
// The GPIO pin needs to be configured as an output.
|
|
sm.set_pindirs([(led_pin_id, hal::pio::PinDir::Output)]);
|
|
sm.start();
|
|
|
|
// PIO runs in background, independently from CPU
|
|
#[allow(clippy::empty_loop)]
|
|
loop {}
|
|
}
|