mirror of
https://github.com/italicsjenga/rp-hal-boards.git
synced 2024-10-17 14:31:31 +11:00
207f5aebdb
We need separate types for any blocking or DMA operations - otherwise, it would not be possible to perform both RX and TX transfers at the same time.
70 lines
2 KiB
Rust
70 lines
2 KiB
Rust
//! This example toggles the GPIO25 pin, using a PIO program.
|
|
//!
|
|
//! If a LED is connected to that pin, like on a Pico board, the LED should blink.
|
|
#![no_std]
|
|
#![no_main]
|
|
|
|
use cortex_m_rt::entry;
|
|
use hal::gpio::{FunctionPio0, Pin};
|
|
use hal::pac;
|
|
use hal::pio::PIOExt;
|
|
use hal::sio::Sio;
|
|
use panic_halt as _;
|
|
use rp2040_hal as hal;
|
|
|
|
#[link_section = ".boot2"]
|
|
#[used]
|
|
pub static BOOT2: [u8; 256] = rp2040_boot2::BOOT_LOADER;
|
|
|
|
#[entry]
|
|
fn main() -> ! {
|
|
let mut pac = pac::Peripherals::take().unwrap();
|
|
|
|
let sio = Sio::new(pac.SIO);
|
|
let pins = hal::gpio::Pins::new(
|
|
pac.IO_BANK0,
|
|
pac.PADS_BANK0,
|
|
sio.gpio_bank0,
|
|
&mut pac.RESETS,
|
|
);
|
|
|
|
// configure LED pin for Pio0.
|
|
let _led: Pin<_, FunctionPio0> = pins.gpio25.into_mode();
|
|
// PIN id for use inside of PIO
|
|
let led_pin_id = 25;
|
|
|
|
// Define some simple PIO program.
|
|
const MAX_DELAY: u8 = 31;
|
|
let mut a = pio::Assembler::<32>::new();
|
|
let mut wrap_target = a.label();
|
|
let mut wrap_source = a.label();
|
|
// Set pin as Out
|
|
a.set(pio::SetDestination::PINDIRS, 1);
|
|
// Define begin of program loop
|
|
a.bind(&mut wrap_target);
|
|
// Set pin low
|
|
a.set_with_delay(pio::SetDestination::PINS, 0, MAX_DELAY);
|
|
// Set pin high
|
|
a.set_with_delay(pio::SetDestination::PINS, 1, MAX_DELAY);
|
|
// Define end of program loop
|
|
a.bind(&mut wrap_source);
|
|
// The labels wrap_target and wrap_source, as set above,
|
|
// define a loop which is executed repeatedly by the PIO
|
|
// state machine.
|
|
let program = a.assemble_with_wrap(wrap_source, wrap_target);
|
|
|
|
// Initialize and start PIO
|
|
let (mut pio, sm0, _, _, _) = pac.PIO0.split(&mut pac.RESETS);
|
|
let installed = pio.install(&program).unwrap();
|
|
let div = 0f32; // as slow as possible (0 is interpreted as 65536)
|
|
let (sm, _, _) = rp2040_hal::pio::PIOBuilder::from_program(installed)
|
|
.set_pins(led_pin_id, 1)
|
|
.clock_divisor(div)
|
|
.build(sm0);
|
|
sm.start();
|
|
|
|
// PIO runs in background, independently from CPU
|
|
#[allow(clippy::empty_loop)]
|
|
loop {}
|
|
}
|