This combines `output_by_name` and `output_by_identifier` into a single
function called `output_by_name_or_id`. This allows for output
identifiers to be used in all commands, simplifies the logic of the
callers, and is more efficient since worst case is a single pass through
the output list.
Moves the call to `terminate_swaybg` from inside `apply_output_config` to
`output_disable`. The former was only called when an output was being
disabled. The latter is called when an output is being disabled and when
an output becomes disconnected. Without this, disconnecting an enabled
output would result in a defunct swaybg process.
This allows for output identifiers and to be used in the `workspace
<workspace> output <outputs...>` command. Previously, only output names
would be allowed. If an output identifier was given, it would never match
an output. This also allows for the wildcard character (`*`) to be
specified, which can be used to generate a list of workspace names that
should be used when generating new workspaces
If there are no arguments or invalid arguments given, swaynag will free
`swaynag.details.button_details` under the `cleanup` label in main. It
then called `swaynag_destroy`, which would attempt to free it again.
Since `swaynag.details.button_details` is either freed on line 106 of
main (when there is no detailed message) or added to `swaynag.buttons`
on line 103 of main, there is no reason to manually free it in
`swaynag_destroy`.
Although I cannot reproduce a double free on my system, for some reason,
it should have actually resulted in a double free in all code paths.
Enables titling views to be dragged by the titlebar. This is in addition
to using the modifier and dragging them from anywhere on the container
surface. Floating views already allow this behavior.
When the cursor surface gets updated, it should be damaged.
This also bumps up `wl_compositor` to version 4 to be able to use
`wl_surface_damage_buffer`.
This fixes a few issues with swaybar's cursor scaling:
1. The cursor scale is now changed when the output scale changes
2. The cursor scale is no longer bound by the max output scale when
swaybar is launched
3. Related to the previous item, the cursor is no longer tiny on low
scale outputs after the max output scale has changed
This also bumps up `wl_compositor` to version 4 to allow usage of
`wl_surface_damage_buffer`.
My previous attempt was not quite right. Changing the focus stack on a
non-visible workspace should only be blocked if the focus would be set
to the workspace itself
Default output configs were generated on reload to reset an output to
its default settings. The idea was that anything that was removed from
the config or changed at runtime and not in the config should be reset
on reload. Originally, they were created using the output name. Recently,
they were changed to use the output identifier. It turns out that there
are issues of shadowing with that solution as well. This should fix
those issues.
Instead of generating the default output configs on reload and storing
them in the output config list to merge on top of, they are now only
generated when retrieving the output config for an output during a
reload. This means that the default output configs are never stored
anywhere and just used as a base to merge unaltered user configs on top
of during a reload.
Starting with a blank output config, merges get applied in the following
order:
1. Default output config (only during a reload)
2. Wildcard config (only if neither output name or output identifier
exist)
3. Output name config
4. Output identifier config
This patch moves view_execute_criteria(view) below the fullscreen code.
Previously, if a view requested to be started in fullscreen, this was
done after execution of criteria and hence it was impossible to disable
fullscreen via criteria.
Fixes#3285
When there are outputs with mixed scales, it was possible for swaybar to
alter `block->separator_block_width` for an output with a higher scale,
and use the changed value for a lower scale output. This caused there to
be larger than normal separation between blocks on the lower scale
outputs. The issue is more obvious the larger the scale difference
between the highest scale output and the lowest scale output.
This fixes the issue by using a local variable that is originally set to
`block->separator_block_width` for rendering, but if it needs to be
increased, the local variable is the only thing touched.
When `block->urgent` is set, use the urgent colors. This matches i3bar's
behavior. Previously, swaybar just ignored the property.
This also adds in rendering for right borders, which was missing.
Changing the focus stack when destroying a container's node on a
non-visible workspace (on an non-focused output) incorrectly causes
the non-visible workspace to become visible. If the workspace is empty,
it will not be destroyed since it is now visible. Additionally since
there was no workspace::focus event, swaybar still shows the previous
workspace as focus-inactive. It also makes no sense to change visible
workspaces due to a container on a non-visible workspace being
destroyed.
Since the focus will either be set when switching to the non-visible
workspace or the workspace will be destroyed due to being empty, there
is no need to change the focus stack when destroying a container on a
non-visible workspace.
Determine the container/workspace a command is run on, each time when a
command of the command list will be run.
Previously the container/workspace was determined only once at the
beginning of command list execution, which led to wrong behaviour
because commands wouldn't take into account when a previous command
changed the focused container.
When generating default output configs to reset the outputs to their
default settings on reload, the output name was being used.
Additionally when determining the output config to apply, if there was
an output config with the output name, that was being used without
checking for an identifier config. This caused sway to completely ignore
the users specified output config.
To fix this issue, the following changes have been made:
1. Default output configs as created for the identifier now instead of
name. This actually makes more sense anyway since you could hotplug
multiple different outputs to the same port.
2. In get_output_config, which is only used to determine which output
config to apply, output configs for both the name and identifier are
queried. If both are found, a new output config is generated with the
identifier config merged on top of the name config. If just one is found,
a copy of that config is returned. This change also requires that the
result from get_output_config be freed after use to prevent memory
leaks, which required some minor changes to logic in
apply_output_config_to_outputs.
If a scratchpad container is hidden, it is still focusable using
criteria and should be shown. This fixes a segfault when attempting to
rebase the cursor since previously the scratchpad container would not be
on any output.
