The original purpose of this commit is to replace some for loops with
list_find. But while doing this I found the workspace_prev_next_impl
functions to be difficult to read and also contained a bug, so I
refactored them and fixed the bug.
To reproduce the bug:
* Have two outputs, where the left output has workspaces 1, 2, 3 and the
right output has workspaces 4, 5, 6. Make workspace 2 focused_inactive
and workspace 4 focused.
* Run `workspace prev`.
* Previously it would visit the left output, then apply `workspace prev`
to workspace 2, which focuses workspace 1.
* Now it will focus the rightmost workspace on the left output
(workspace 3).
The refactoring I made to the workspace functions are:
* Added the static keyword.
* They now accept an int dir rather than bool, to avoid an unnecessary
conversion.
* Rather than preparing start and end variables for the purpose of
iterating, just iterate everything.
* Replace for loops with list_find.
* Don't call workspace_output_prev_next_impl (this fixes the bug).
Rationale: Sticky containers are always assigned to the visible
workspace.
The basic idea here is to check the destination's output (move.c:190).
But if the command was `move container to workspace x` then a workspace
might have been created for it. We could destroy the workspace in this
case, but that results in unnecessary IPC events.
To avoid this, the logic for `move container to workspace x` has been
adjusted. It now delays creating the workspace until the end, and uses
`workspace_get_initial_output` to determine and check the output before
creating it.
* Removes container_floating_move_to_container, instead opting to put
that logic in container_move_to
* In the seat code, focusing a floating view now updates the pending
state only and lets the next transaction carry it over to the current
state. This is required, otherwise it would crash.
* When unfullscreening a floating container, an output check is now done
to see if it should center it.
In a multi-output setup, if a sticky container is on one output and
focus is on the other output, and you run (eg) `workspace 1` to focus
the workspace containing the sticky container, an infinite loop would
occur. It would loop infinitely because it would remove the sticky
container from the workspace, add it back to the same workspace, and
then decrement the iterator variable.
The fix just wraps the loop in a workspace comparison.
container_move_to handled moving containers to new parents, as well as
moving workspaces to new outputs.
This commit removes the workspace-moving code from this function and
introduces workspace_move_to_output. Moving workspaces using
container_move_to only happened from the move command, so it's been
implemented as a static function in that file.
Simplifying container_move_to makes it easier for me to fix some issues
in #2420.
I've got the following SIGSEGV when terminating sway:
```
Program terminated with signal SIGSEGV, Segmentation fault.
0x00005607dc603af5 in view_unmap (view=0x5607dcb3d350) at ../sway/tree/view.c:599
599 if (surviving_ancestor->type >= C_WORKSPACE) {
```
surviving_ancestor was NULL at that time
This commit is trying to fix this problem.
This creates a root.c and moves bits and pieces from elsewhere into it.
* layout_init has been renamed to root_create and moved into root.c
* root_destroy has been created and is called on shutdown
* scratchpad code has been moved into root.c, because hidden scratchpad
containers are stored in the root struct
Calling container_at_view fails an assertion if the container isn't a
view. Calling tiling_container_at works correctly, as that function
checks if the container is a view and calls container_at_view if so.
When a view unmaps, normally the surviving ancestor (ie. after reaping)
needs to be arranged. When a fullscreen view unmaps, it arranges the
workspace rather than the surviving ancestor, but didn't handle cases
where the workspace itself was reaped. This happens if the workspace is
not currently shown and the fullscreen view was the last container on
that workspace.
This commit rewrites this part of view_unmap so it's more readable, and
fixes the crash by not arranging the workspace if it's been reaped. Note
that it no longer arranges the output under any circumstance - this
wasn't required anyway.
* seat_set_focus_warp lacked a container NULL check
* view mapping code needs to use seat_get_focus_inactive
Also, seat_set_focus_warp triggered the wrong IPC event if focus was a
workspace, which resulted in swaybar not showing the workspace as
active.
When a container is moved from, say, workspace 1 to workspace 2, workspace 2 is focused in order to arrange the windows before focus is moved back to workspace 1, which caused a workspace:focus event from workspace 2 to workspace 1 to be emitted. This commit inhibits that event.
Fixes#2364.
Suppose a view is 600px wide, and we tell it to resize to 601px during a
resize operation. We create a transaction, save the 600px buffer and
send the configure. This buffer is saved into the associated
instruction, and is rendered while we wait for the view to commit a
601px buffer.
Before the view commits the 601px buffer, suppose we tell it to resize
to 602px. The new transaction will also save the buffer, but it's still
the 600px buffer because we haven't received a new one yet.
Then suppose the view commits its original 601px buffer. This completes
the first transaction, so we apply the 601px width to the container.
There's still the second (now only) transaction remaining, so we render
the saved buffer from that. But this is still the 600px buffer, and we
believe it's 601px. Whoops.
The problem here is we can't stack buffers like this. So this commit
removes the saved buffer from the instructions, places it in the view
instead, and re-saves the latest buffer every time the view completes a
transaction and still has further pending transactions.
As saved buffers are now specific to views rather than instructions, the
functions for saving and removing the saved buffer have been moved to
view.c.
The calls to save and restore the buffer have been relocated to more
appropriate functions too, favouring transaction_commit and
transaction_apply rather than transaction_add_container and
transaction_destroy.
Fixes the render and container_at order for popups.
Fixes#2210
For rendering:
* render_view_surfaces has been renamed to render_view_toplevels
* render_view_toplevels now uses output_surface_for_each_surface (which
is now public), as that function uses wlr_surface_for_each_surface which
doesn't descend into popups
* Views now have a for_each_popup iterator, which is used by the
renderer to render the focused view's popups
* When rendering a popup, toplevels (xdg subsurfaces) of that popup are
also rendered
For sending frame done, the logic has been updated to match the
rendering logic:
* send_frame_done_container no longer descends into popups
* for_each_popup is used to send frame done to the focused view's popups
and their child toplevels
For container_at:
* floating_container_at is now static, which means it had to be moved
higher in the file.
* container_at now considers popups for the focused view before checking
containers.
* tiling_container_at has been introduced, so that it doesn't call
container_at recursively (it would check popups recursively if it did)
Example config that produces the crash (with a single output):
workspace 1
workspace 2
Prior to this commit, container_workspace_free would manually mark the
L_FLOATING container as destroying and free it. This assumed the
L_FLOATING container would never be involved in a transaction. This was
a safe assumption when it was implemented, but became an incorrect
assumption once parent/child relationships became transactionised.
This commit removes the L_FLOATING free from container_workspace_free.
When the workspace is destroyed, it starts the normal destroy process on
the L_FLOATING container so it can be freed via transactions.
