* `bindsym --to-code` enables keysym to keycode translation.
* If there are no `xkb_layout` commands in the config file, the translation
uses the XKB_DEFAULT_LAYOUT value.
* It there is one or more `xkb_layout` command, the translation uses
the first one.
* If the translation is unsuccessful, a message is logged and the binding
is stored as BINDING_KEYSYM.
* The binding keysyms are stored and re-translated when a change in the input
configuration may affect the translated bindings.
This modifies cmd_move to allow for the syntax options allowed by i3.
The following syntaxes are supported:
- `move left|right|up|down [<amount> [px]]`
- `move [--no-auto-back-and-forth] [window|container] [to] workspace
<name>|next|prev|next_on_output|prev_on_output|current|number <num>`
- `move [window|container] [to] output <name/id>|left|right|up|down`
- `move [window|container] [to] mark <mark>`
- `move workspace to [output] <name/id>|left|right|up|down`
- `move [window|container] [to] [absolute] position <x> [px] <y> [px]`
- `move [window|container] [to] [absolute] position center`
- `move [window|container] [to] position mouse|cursor|pointer`
This also allows retains the following syntax option that is not
supported by i3, but is supported in sway 1.0:
- `move workspace [to] output <name/id>|left|right|up|down`
The changes are:
- `window` and `container` are now optional
- `output` is now optional for `move workspace` when `to` is given
There is also stricter command checking now. If `absolute` or
`--no-auto-back-and-forth` are given for commands that do not support
them, it will be treated as invalid syntax instead of being silently
ignored.
Disable the i3-compatible behavior if the option '--i3' is not given.
Previously it was only possible to disable it by changing the config
file. Now it also works via swaymsg.
When setting fullscreen on a hidden scratchpad container, there was a
check to see if there was an existing fullscreen container on the
workspace so it could be fullscreen disabled first. Since the workspace
is NULL, it would cause a SIGSEGV. This adds a NULL check to avoid the
crash.
This also changes the behavior of how fullscreen is handled when adding
a container to the scratchpad or changing visibility of a scratchpad
container to match i3's. The behavior is as follows:
- When adding a container to the scratchpad or hiding a container back
into the scratchpad, there is an implicit fullscreen disable
- When setting fullscreen on a container that is hidden in the
scratchpad, it will be fullscreen when shown (and fullscreen disabled
when hidden as stated above)
- When setting fullscreen global on a container that is hidden in the
scratchpad, it will be shown immediately as fullscreen global. The
container is not moved to a workspace and remains in the
scratchpad. The container will be visible until fullscreen disabled
or killed. Since the container is in the scratchpad, running
`scratchpad show` or `move container to scratchpad` will have no
effect
This also changes `container_replace` to transfer fullscreen and
scratchpad status.
This makes it so there will only be one swaybg instance running
instead of one per output. swaybg's cli has been changed to a xrandr
like interface, where you select an output and then change properties
for that output and then select another output and repeat. This also
makes it so swaybg is only killed and respawned when a background
changes or when reloading.
This implements the following command to set/unset a user idle
inhibitor for a view:
`inhibit_idle focus|fullscreen|open|none|visible`
The modes are as follows:
- focus: inhibited when the view is focused by any seat
- fullscreen: inhibited when the view is fullscreen (or a descendant of
a fullscreen container) and is visible on any output
- open: inhibited until the view is closed or the inhibitor is unset or
changed
- none: unsets any user set idle inhibitors for the view
- visible: inhibited when the view is visible on any output
This should have no effect on idle inhibitors set by the applications
themselves and those should still work as intended.
Since this operates on the view in the handler context, it is possible
to set it on the currently focused view, on any existing view with
criteria, or for any future view with for_window.
Many laptop screens report unknown subpixel order. Allow users to manually set subpixel hinting to work around this.
Addresses https://github.com/swaywm/sway/issues/3163
This change adds support for renaming a workspace when `exec` command
is being processed by keeping sway_workspace and pid_workspace names in
sync.
The change can be verified by running following command:
swaymsg exec <application>; swaymsg rename workspace number 1 to 5
Fixes: #3952
This kind of worked before in that focus would change, but it wasn't
intentionally supported and had side effects such as not raising
the container, and being unable to cycle through all floaters depending
on the direction used.
This commit makes it properly supported. The new focus is chosen based
on the distance to the center point of each floating container in the
workspace, and the container is raised.
In a multi output setup, if both visible workspaces have floating
containers, focus will NOT cross into the other output. It is assumed
the user will use a workspace binding in this case.
If two floating containers occupy the exact same center point and you
try to focus in a direction, the behaviour is undefined.
This commit adds support for laptop lid and tablet
mode switches as provided by evdev/libinput and
handled by wlroots.
Adds a new bindswitch command with syntax:
bindswitch <switch>:<state> <command>
Where <switch> is one of:
tablet for WLR_SWITCH_TYPE_TABLET_MODE
lid for WLR_SWITCH_TYPE_LID
<state> is one of:
on for WLR_SWITCH_STATE_ON
off for WLR_SWITCH_STATE_OFF
toggle for WLR_SWITCH_STATE_TOGGLE
(Note that WLR_SWITCH_STATE_TOGGLE doesn't map to
libinput and will trigger at both on and off events)
This changes the way zero (which is the default) is interpreted for both
the width and height of `floating_maximum_size`. It now refers to the
width and height of the entire output layout, which matches i3's
behavior.
This also removes duplicated code to calculate the floating constraints
in three files. Before this, `container_init_floating` used two-thirds
of the workspace width/height as the max and the entire workspace
width/height was used everywhere else. Now, all callers use a single
function `floating_calculate_constraints`.
Enables i3-compatible behavior regarding hiding the title bar on tabbed and
stacked containers with one child.
Related issues and merge requests: #3031, #3002, #2912, #2987.
This makes it so running `move [to] scratchpad` on a container already
in the scratchpad does not return an error. To match i3's behavior, a
visible scratchpad container will be hidden and a hidden scratchpad
container will be treated as a noop.
This modifies the places where output_get_active_workspace is called to
handle a NULL result. Some places already handled it and did not need a
change, some just have guard off code blocks, others return errors, and
some have sway_asserts since the case should never happen. A lot of this
is probably just safety precautions since they probably will never be
called when `output_get_active_workspace` is not fully configured with a
workspace.
This fixes a few misc memory leaks reported by asan:
- Items of `config->config_chain` are now freed instead of just the list
itself
- `bar->swaybar_command` is now freed
- The result returned by a seat subcommand is now returned instead of
leaked
If the bar was set to "invisible" and subsequently "toggle" was send twice, the
new mode was never set and the bar->mode was double freed.
Fix this by not requiring the bar->mode to be "hide" and instead show it
unconditionally, because it was either hidden or invisible.
Fixes#3637
sway-bar(5) documents `modifier none`, which comes from i3. This
implements the functionality for `modifier none` since it was not
previously implemented. The bar modifier toggles visibility of the bar
when the bar mode is set to hide. When the bar modifier is set to
`none`, the ability to toggle visibility of the bar will be disabled.
If output_cmd_background is given a valid mode as the first argument,
then there is no file given and an error should be returned.
join_args should not be called with an argc of zero since it sets the
last character to the null terminator. With an argc of zero, the length
is zero causing a heap buffer overflow when setting the byte before the
start of argv to '\0'. This probably will not ever generate a segfault,
but may cause data corruption to whatever is directly before it in
memory. To make other such cases easier to detect, this also adds a
sway_assert in join_args when argc is zero.
This fixes a double free in cmd_workspace_gaps when the amount given is
invalid. The end pointer from strtol is part of the argument and should
not be freed. Freeing the end pointer could result in a double free or
bad free depending on whether or not the end pointer was at the start of
the argument
If a seat does not exist in seat_cmd_cursor, do not create it. A seat
without any attachments is useless since it will have no capabilities.
This changes `input_manager_get_seat` to have an additional argument
that dictates whether or not to create the seat if it does not exist.
This allows for `-` (hyphen) to be used as an alias for the current seat
while sway is running. This alias was chosen since it is unlikely to
interfere with any desirable seat identifier
This changes the `pointer_constraint` command to be a subcommand of seat
to allow for per-seat settings. The current implementation that is not a
seat subcommand will only operate on the current seat and will segfault
in the config due to `config->handler_context.seat` only being set at
runtime.
This also allows for the wildcard identifier to be used to alter the
pointer constraint settings on all seats and allows for the setting to
be merged with the rest of the seat config.
