If GPIO23 is low, the power supply is in low-power mode. But it
generates some noise. If GPIO23 is high, the power supply is less
efficient, but it generates less noise too.
Start to address #186 (Safety requirement must be verbosely advertised to not be overlooked in future changes).
#177 (Mark PIO StateMachine, Rx and Tx as Send) added the Send trait to StateMachine, Tx and Rx, That documentation was expanded as suggested.
PIO, UninitStateMachine, Interrupt were marked Send before #177, added some documentation to those as well.
* Implement peripheral support for i2c and an advanced example for the pico board.
* Simplify i2c peripheral bootstrap and add a "free" function to allow switching modes.
* Set dependency to futures & nostd_async to specific version/revision.
* move enum & struct to the start of the file
* Add a bit of documentation to the pico_i2c_controller_peripheral demo.
* Migrate to pico_i2c_controller_peripheral to embassy & simplify the peripheral support
nostd_async is broken since last stable roll out.
The pico_i2c_controller_peripheral is being migrated to use embassy's executor.
The Controller Async API is now aligned with embassy's traits to facilitate integration.
The peripheral no longer require async to run and now appears as an event iterator.
Embassy's support relies on unstable features (generic_associated_types and type_alias_impl_traits)
and is therefore gated behind the `embassy-traits` feature flag.
* make futures & embassy optional for the pico board too
* Pin embassy to a specific rev.
* Impl embassy_traits::i2c::WriteIter & enable unlimited transfer size on i2c
* Applies comment suggestion from @9names for the advanced i2c example.
Co-authored-by: 9names <60134748+9names@users.noreply.github.com>
* use `I2C block` instead of `IP`.
* Fix formatting (unnecessary space at end of line)
* Enhance explanation for why `rd_req()` is not cleared in `Iterator::next`'s
implementation.
Co-authored-by: 9names <60134748+9names@users.noreply.github.com>
* Created an itsy bitsy rp2040 board support package adapted from the bsp of the qt py rp2040. Special thanks to ithinuel for help in matrix
* Changed the board description so it doesn't match the qt py rp2040
* Changed blinky.rs to itsy_bitsy_blinky.rs and ran changes through cargo fmt
* Add pico_i2c_pio example
* Update pico_i2c_pio's main function documentation
* Update bootloader reference.
* Implement uart output for the pico_i2c_pio example.
* pin to a specific rev of i2c-pio
* Bump i2c-pio to get the fix for write_read
* Use volatile register access for gpio interrupts
* Provide functions for atomic register updates
* Use atomic register access functions in pio.rs
* Improve doc comments
* Limit visibility of atomic register access functions
Also remove write_xor for now, as it's not yet used anywhere
* Implements methods to allow presetting the pin state & direction
Enabling those methods allows to save a few valuable instructions
in the PIO's memory.
* Use IntoIterator rather than Iterator.
* Use proper types instead of bool to be more idiomatic.
* Change set_pindirs_with_mask to a more idiomatic rust approach.
* Update pio_proc_blink with new set_pindirs_with_iter
* Force reset on startup to guaranty consistency with type-states.
* Expose more accessors to allow more advanced driver to be implemented.
* Add the ability to restart the state machine from its wrap point.
This method also clears the ISR/OSR to give the state machine a clean
restart.
* Add a comment about the impact of autopull on OUT & PULL instructions
* Fix broken internal doc reference & add an important note on Tx<SM>::has_stalled
* rename block methods to register_block.
This change is made to avoid confusion with "block" as a verb.
* Implements methods to allow presetting the pin state & direction
Enabling those methods allows to save a few valuable instructions
in the PIO's memory.
* Update pio_proc_blink with new set_pindirs
