mirror of
https://github.com/italicsjenga/rp-hal-boards.git
synced 2024-12-25 21:41:31 +11:00
6ae0698b7a
* Update BSP README's to use current version number * Update ws2812-pio and i2c-pio to release 0.3.0 * Bump patch number for BSPs so we can push with correct docs
142 lines
4.9 KiB
Markdown
142 lines
4.9 KiB
Markdown
# [rp-pico] - Board Support for the [Raspberry Pi Pico]
|
|
|
|
You should include this crate if you are writing code that you want to run on
|
|
a [Raspberry Pi Pico] - the original launch PCB for the RP2040 chip.
|
|
|
|
This crate includes the [rp2040-hal], but also configures each pin of the
|
|
RP2040 chip according to how it is connected up on the Pico.
|
|
|
|
[Raspberry Pi Pico]: https://www.raspberrypi.org/products/raspberry-pi-pico/
|
|
[rp-pico]: https://github.com/rp-rs/rp-hal/tree/main/boards/rp-pico
|
|
[rp2040-hal]: https://github.com/rp-rs/rp-hal/tree/main/rp2040-hal
|
|
[Raspberry Silicon RP2040]: https://www.raspberrypi.org/products/rp2040/
|
|
|
|
## Using
|
|
|
|
To use this crate, your `Cargo.toml` file should contain:
|
|
|
|
```toml
|
|
rp-pico = "0.4.0"
|
|
```
|
|
|
|
In your program, you will need to call `rp_pico::Pins::new` to create
|
|
a new `Pins` structure. This will set up all the GPIOs for any on-board
|
|
devices. See the [examples](./examples) folder for more details.
|
|
|
|
## Examples
|
|
|
|
### General Instructions
|
|
|
|
To compile an example, clone the _rp-hal_ repository and run:
|
|
|
|
```console
|
|
rp-hal/boards/rp-pico $ cargo build --release --example <name>
|
|
```
|
|
|
|
You will get an ELF file called
|
|
`./target/thumbv6m-none-eabi/release/examples/<name>`, where the `target`
|
|
folder is located at the top of the _rp-hal_ repository checkout. Normally
|
|
you would also need to specify `--target=thumbv6m-none-eabi` but when
|
|
building examples from this git repository, that is set as the default.
|
|
|
|
If you want to convert the ELF file to a UF2 and automatically copy it to the
|
|
USB drive exported by the RP2040 bootloader, simply boot your board into
|
|
bootloader mode and run:
|
|
|
|
```console
|
|
rp-hal/boards/rp-pico $ cargo run --release --example <name>
|
|
```
|
|
|
|
If you get an error about not being able to find `elf2uf2-rs`, try:
|
|
|
|
```console
|
|
$ cargo install elf2uf2-rs
|
|
```
|
|
then try repeating the `cargo run` command above.
|
|
|
|
### [pico_blinky](./examples/pico_blinky.rs)
|
|
|
|
Flashes the Pico's on-board LED on and off.
|
|
|
|
### [pico_gpio_in_out](./examples/pico_gpio_in_out.rs)
|
|
|
|
Reads a push button attached to GPIO 15 and drives the on-board LED to match it (i.e. on when pressed, off when not pressed).
|
|
|
|
### [pico_rtic](./examples/pico_rtic.rs)
|
|
|
|
Demonstrates the use of the [Real-Time Interrupt-driven Concurrency Framework] on the Raspberry Pi Pico.
|
|
|
|
[Real-Time Interrupt-driven Concurrency Framework]: https://rtic.rs
|
|
|
|
### [pico_countdown_blinky](./examples/pico_countdown_blinky.rs)
|
|
|
|
Another LED blinking example, but using a Timer in count-down mode.
|
|
|
|
### [pico_pwm_blink](./examples/pico_pwm_blink.rs)
|
|
|
|
Puts out an analog 'triangle wave' on GPIO 25, using the PWM hardware.
|
|
|
|
### [pico_pwm_servo](./examples/pico_pwm_servo.rs)
|
|
|
|
Demonstrates handling a micro servo, using the PWM hardware.
|
|
|
|
### [pico_usb_serial](./examples/pico_usb_serial.rs)
|
|
|
|
Creates a USB Serial device on a Pico board.
|
|
|
|
The USB Serial device will print `HelloWorld` on start-up, and then echo any
|
|
incoming characters - except that any lower-case ASCII characters are
|
|
converted to the upper-case equivalent.
|
|
|
|
### [pico_usb_serial_interrupt](./examples/pico_usb_serial_interrupt.rs)
|
|
|
|
Creates a USB Serial device on a Pico board, but demonstrating handling
|
|
interrupts when USB data arrives.
|
|
|
|
### [pico_usb_twitchy_mouse](./examples/pico_usb_twitchy_mouse.rs)
|
|
|
|
Demonstrates emulating a USB Human Input Device (HID) Mouse. The mouse
|
|
cursor will jiggle up and down.
|
|
|
|
### [pico_spi_sd_card](./examples/pico_spi_sd_card.rs)
|
|
|
|
Example that shows how to use the
|
|
[embedded_sdmmc crate](https://github.com/rust-embedded-community/embedded-sdmmc-rs)
|
|
with the Raspberry Pi Pico.
|
|
|
|
## Contributing
|
|
|
|
Contributions are what make the open source community such an amazing place to
|
|
be learn, inspire, and create. Any contributions you make are **greatly
|
|
appreciated**.
|
|
|
|
The steps are:
|
|
|
|
1. Fork the Project by clicking the 'Fork' button at the top of the page.
|
|
2. Create your Feature Branch (`git checkout -b feature/AmazingFeature`)
|
|
3. Make some changes to the code or documentation.
|
|
4. Commit your Changes (`git commit -m 'Add some AmazingFeature'`)
|
|
5. Push to the Feature Branch (`git push origin feature/AmazingFeature`)
|
|
6. Create a [New Pull Request](https://github.com/rp-rs/rp-hal/pulls)
|
|
7. An admin will review the Pull Request and discuss any changes that may be required.
|
|
8. Once everyone is happy, the Pull Request can be merged by an admin, and your work is part of our project!
|
|
|
|
## Code of Conduct
|
|
|
|
Contribution to this crate is organized under the terms of the [Rust Code of
|
|
Conduct][CoC], and the maintainer of this crate, the [rp-rs team], promises
|
|
to intervene to uphold that code of conduct.
|
|
|
|
[CoC]: CODE_OF_CONDUCT.md
|
|
[rp-rs team]: https://github.com/orgs/rp-rs/teams/rp-rs
|
|
|
|
## License
|
|
|
|
The contents of this repository are dual-licensed under the _MIT OR Apache
|
|
2.0_ License. That means you can choose either the MIT license or the
|
|
Apache-2.0 license when you re-use this code. See `MIT` or `APACHE2.0` for more
|
|
information on each specific license.
|
|
|
|
Any submissions to this project (e.g. as Pull Requests) must be made available
|
|
under these terms.
|